\u00a9 2021 wikiHow, Inc. All rights reserved. Can you install carpet without a stretcher? They're also good as spacers between sheets of material. The job also requires some more common tools, such as a hammer, measuring tape, hand stapler, and various cutting tools. Include your email address to get a message when this question is answered. Wear heavy duty gloves when working with tack strips. For small, round patches, there's a tool called a cookie cutter -- it's about 3-4 inches in diameter. "This article opened my mind regarding installing a carpet. Finally, finish with your edges. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. Approved. My carpet is curved so the z bar was cut into smaller pieces to match. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. If moisture did get through the concrete, any kind of primer in the world would release and bubble. Mark Spelman is a General Contractor based in Austin, Texas. There are 22 references cited in this article, which can be found at the bottom of the page. wikiHow marks an article as reader-approved once it receives enough positive feedback. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. Get something that'll serve your purpose, but don't get pushed into expensive options you don't want. To install carpet, start by nailing the tack strips to the floor, using 2 nails for each strip. All tip submissions are carefully reviewed before being published, This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. On concrete, you may be able to just pound it in the same way if the concrete is soft enough. Can I put tack strips over padding then put carpet into strips? Carpet is installed using glue or tack strips. You can tuck the carpet right to your hardwood floor. Step 2: Remove Staples, Nails or Tack Strips After removing the carpet, dispose of the carpet pad. But with the arrival of COVID-19, the stakes are higher than ever. No, but if you don't remove them, the chance of them being nicked or damaged is very high. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. For example, if one wall has a small part that dips out, measure the 2 walls and then increase your estimate by 1 foot (0.30 m) on that wall. No, baseboards do not need to be removed. Both terms are used interchangeably but floor covering refers more to loose-laid materials. Consider carpet made from olefin face fiber. Thirdly, you could pre-drill holes for the masonry nails (about 1/16") of smaller than the nail. % of people told us that this article helped them. Install dimpled polyethylene to create an air space between the concrete and the sub floor or a 6-mil layer of plastic to separate the underpadding from the concrete. I just flung that thing under them and pushed down. For example, if your room was 13 by 10 feet (4.0 by 3.0 m), then you multiply 13 by 10 to get 130 square feet (12 m. When deciding on tack strips, opt for the widest you can find. For tips on trimming the carpet once it's in place, read on! I wasn't aware of a large mechanical carpet stretching device. This image may not be used by other entities without the express written consent of wikiHow, Inc.
\n<\/p>

\n<\/p><\/div>"}, {"smallUrl":"https:\/\/www.wikihow.com\/images\/thumb\/b\/b0\/Install-Carpet-Step-4-Version-3.jpg\/v4-460px-Install-Carpet-Step-4-Version-3.jpg","bigUrl":"\/images\/thumb\/b\/b0\/Install-Carpet-Step-4-Version-3.jpg\/aid179411-v4-728px-Install-Carpet-Step-4-Version-3.jpg","smallWidth":460,"smallHeight":345,"bigWidth":728,"bigHeight":546,"licensing":"